Sunways STH-10K-HT User Manual Download Page 7

12

13

     

Mode 5

In the purely off-grid mode, power 
from PV will supply the back-up 
loads first and then charge the 
battery if there’re surplus.

     

Mode 3

In this working mode, the inverter 
will use the power from PV or 
grid (Set in the App) to charge the 
battery until it is fully charged, 
and as long as the grid is there, 
the battery won’t discharge.
When the grid is cut off, power 
from PV and battery will supply to 
the loads connected in the back-
up side (UPS).

When the power from PV isn’t 
enough, the battery will discharge 
to supply back-up loads together 
with PV.

     

Mode 4

In this working mode, you can set 
charge/discharge power and time 
in the App, inverter will use the 
power from PV or grid(whether 
to  use  can  be  set  in  the  App) 
to  charge  the  battery  in  the 
predetermined period.

Inverter will use power from PV 
and battery to supply loads in the 
predetermined period and the 
insufficient part will be supplied 
by the grid.

No Grid

No Grid

×

3.1.6 Off-grid Output Ability (UPS Ability)
Sunways STH hybrid inverter supports max 2times off-grid instantaneous overload of rated 
output power, and each phase support 1.25times continuous overload of rated output power 
but only one of them can reach 1.25times output power at the same time.
3.1.7 Storage conditions
1) Inverter must be stored in its original packaging.
2) The storage temperature should be in the range of -30 ° C and + 60 ° C, and the relative 
humidity stored is less than 90%.
3) If a batch of inverters needs to be stored, the height of each pile should be no more 
than 6 levels.

PV

PV

PV

PV

PV

Inverter

Inverter

Inverter

Inverter

Inverter

Load

Load

Load

Load

Load

Grid

Grid

Grid

Battery

Battery

Battery

Battery

Battery

Summary of Contents for STH-10K-HT

























Reviews: