manualshive.com logo in svg

Sunways NTX3000, User Manual

Share
Download
Sunways NTX3000 User Manual Download Page 33

7   Display and messages

33

7.2  Available Data

The NTX inverter provides two types of data that 
can be collected using the NTX Communicator inter-
face software.

Real-time operational data

Real-time operational data can be transmitted on 
demand through the communication and display on 
LCD. They are not stored by inverter. The NTX com-
municator software (available on the installation 
CD) may be used to transmit data to PC.

The following data is available:

 · Grid voltage
 · Grid current 
 · Grid frequency
 · Power transferred to the grid
 · Voltage of photovoltaic array 1
 · Current of photovoltaic array 1
 · Voltage of photovoltaic array 2
 · Current of photovoltaic array 2
 · Serial number/Part number
 · Firmware revision code
 · Daily energy 
 · Monthly energy
 · Total energy
 · Leakage current to ground
 · Date, time

Internally logged data

The NTX inverter stores internally the following data 
you can query through LCD or PC monitor software.

 · Today’s lifetime counter of energy transferred to 

the grid.

 · This month’s lifetime counter of energy trans-

ferred to the grid.

 · Total lifetime counter of energy transferred to 

the grid.

 · Last 50 fault conditions with error code and time 

stamp.

 · Last 50 start and stop time of energy transferred 

to the grid.

7.3  LCD display and operation

The two-line Liquid Crystal Display is located on the 
front panel and shows:

 · Inverter operating status and statistics,

 · Service messages for the operator,

 · Error messages and fault indications.

Display upon start-up

During normal conditions, the LCD backlight will be 
turn on first upon start-up, and the backlight shuts 
off automatically after 1 minutes.

The following messages are displayed during initial-
ization of the inverter:

1.  Starting up (remain 5 seconds)

Welcome to use

Sunways Inverter

2.  Waiting 

After starting up the system go to waiting state, 
and the LCD will display following 5 screens mes-
sages in turn.

Welcome to use

Sunways Inverter

Waiting

Waiting Sun

Waiting.

Waiting Sun

Welcome to use

Sunways Inverter

Waiting.

Waiting Sun

Waiting.

Waiting Sun

Welcome to use

Sunways Inverter

Waiting..

Waiting Sun

Waiting.

Waiting Sun

Welcome to use

Sunways Inverter

Waiting...

Waiting Sun

Waiting....

Waiting Sun

The display changes to next screen every half 
second.

Summary of Contents for NTX3000

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands