SunStar 867 Series User Manual Download Page 13

Page: 13 / 36

5) Adjustment of belt tension

Once the motor is installed, when the fixing nuts

①

②

are

fully unfastened on both sides, tension is created to the belt

④

due to the weight of the motor

③

. At this moment, fasten

the fixing nut

①

first, then fasten the fixing nut

②

tightly.

(See figure 7)

[Figure 7]

④

③

①

②

6) Installation of program unit

(automatic trimming type)

(1) Fix the bracket

②

onto the program unit

①

, using 4

fixing nuts

③

(2) Then, use 3 fixing bolts

④

to tightly fix the bracket

②

where the program unit

①

has been attached, along with

the back cover. (see figure 8)

[Figure 8]

①

②

④

③

7) Installation of belt cover

(1) Attach belt cover

“

”

onto the back of the machine body as seen in figure 9.

(2) As seen in figure 10, assemble the belt cover support pin

①

to the arm base

②

, and then attach the belt cover

“

”

to the

machine. Now, if a bobbin winder is attached on the table, lay down the machine body on its back and attach the belt

cover

“

”

(3) Fix the belt covers

“

”

and

“

”

as can be seen on part

“

”

of the figure.

(4) Fix the lower part of the belt cover

“

”

onto the machine bed like part

“

”

of the figure.

[Figure 10]

[Figure 9]

“A”

“K”

①

②

“A”

“B”

“Q”

Summary of Contents for 867 Series





































Search results

Summary of Contents for 867 Series

Reviews:

Related manuals for 867 Series

Brands by name

Popular brands

SunStar 867 Series, User Manual

Search results

Summary of Contents for 867 Series

Reviews:

Related manuals for 867 Series

Brands by name

Popular brands