SunStar 867 Series User Manual Download Page 27

Page: 27 / 36

B) Adjusting the stopper pin holder (See figure 42)

a) Make sure to turn the machine pulley to place the trimming cam

③

in the right position, so that the roller

①

can

enter the complementary straight line

②

range after finishing trimming marked in the trimming cam lead.

b) Press down the trimmer shake linkage

④

to make the roller

①

come inside the trimming cam

③

ⓐ

Adjust the holder

⑦

to make the right equal point of the roller

①

adhere

⑤

smoothly to the inner right side of

the cam’s complementary straight line

②

, and the left equal point of the stopper pin

⑥

adhere

⑧

smoothly to

the inner left side of the stopper pin holder

⑦

. Once this is done, tightly fasten the fixing screw

⑨

ⓑ

Once such adjustments are made, the trimmer shake linkage

④

will not move even when shaken to its sides (the

roller is inside the cam). Make sure to check if the shake linkage

④

returns to up position

⑩

quickly and

smoothly when released. If not, proceed with horizontal adjustment of stopper pin holder

⑦

[Figure 42]

(

※

The present stop position of the cam: roller is inside
the complementary straight line with the cam lead,
right before it exits having finished trimming action)

Complementary straight line

②

①

⑨

④

⑤

③

①

⑩

⑥

⑧

⑦

Trimming finishing point

Movable knife operation
starting point

[Trimming Cam Lead]

Summary of Contents for 867 Series





































Search results

Summary of Contents for 867 Series

Reviews:

Related manuals for 867 Series

Brands by name

Popular brands

SunStar 867 Series, User Manual

Search results

Summary of Contents for 867 Series

Reviews:

Related manuals for 867 Series

Brands by name

Popular brands