manualshive.com logo in svg

Sunrain BYC-007TF1, Installation & Operation Manual, Page: 4 / 28

Share
Download
Sunrain BYC-007TF1 Installation & Operation Manual Download Page 4

- 4 -

Please keep installation manual properly, and read it carefully before using.

The unit must be installed by professional personnel according to the instructions in this manual.

WARNING: if the unit is installed in locations that are at risk of lightning strikes, lightning

protection measures must be provided.

WARNING: The unit is not suitable for use in winter: all water must be drained from the unit during

winter or it could freeze inside the unit causing damage to the internal components.

Content

Accessories……………............................................................................5

Safety.........................................................................................................6

Heat pump working principle..................................................................7

Installation of the unit..............................................................................8

Installation of the pipeline.....................................................................10

Installation of optional accessories......................................................13

Installation and operation of electric devices......................................14

Instruction for operation .......................................................................17

Initial operation and setting ..................................................................22

Operation and maintenance...................................................................23

Fault analysis and solution method………………................................25

Technical parameters.............................................................................26

After-sale service....................................................................................27

Summary of Contents for BYC-007TF1





























Reviews:

No comments