manualshive.com logo in svg

Sunoptics EZY CURB EZYSA, Installation Manual, Page: 12 / 14

Share
Download
Sunoptics EZY CURB EZYSA Installation Manual Download Page 12

For questions or concerns, please visit us at www.sunoptics.com, or call your nearest Sunoptics representative. 

SUNOPTICS

® | 6201 27th Street, Sacramento, CA 95822 | 916.395.4700 | 800.289.4700 |  

www.sunoptics.com

 

 

Page 12 of 14

 

25.

 

Place butyl tape on the starter panel on all interface surfaces, see below in blue (both sides).  Apply a ¼” 
bead of metal construction sealant at the location seen below in orange (both sides).  

 

 

26.

 

Place starter panel (#3) onto rails, then press down to make sure it is fully down in place. 

 

27.

 

Place butyl tape on starter panel flange and rail as pictured below.  Then apply an L‐shaped ¼” bead of 
sealant at the location indicated below in orange on both sides. 

 

 

28.

 

Place starter panel cap (#5) onto starter panel and secure down with (2) 1” concealer head screws (#11) 
fastened vertically indicated by the green dot below.  Then fasten horizontally with (4) 1.5” Concealer 
Pancake Head w/ EPDM washer screws (#12) using the pre‐drilled holes as position indicators.  

 

 

 

Summary of Contents for EZY CURB EZYSA















Reviews:

No comments