My booth won’t work with the T-Max® Manager remote system
1.
The booth must first be set to a unique address, see Remote
Connections.
2.
The bypass plug may be installed in the series in an inap-
propriate location. Remove bypass plugs when using TMax®
products.
When auto-addressing the first bed does not register an address
When using the auto address feature of the T-Max® Manager
you must wait 10 seconds from the time you start the auto ad-
dress function before addressing the first bed.
I forgot what address I set my booth to
By pressing the stop button and then the timer button, and
holding both for 3 seconds, the timer display will show the
booth’s address number. Press the stop button to exit address
mode.
My both is connected to the T-Max® Manager remote system and
when the delay time has expired the timer display starts counting
down but the booth lights do not come on
The auto start feature of the remote system is disabled, see the
instructions provided with your remote system.
My booth, connected to a T-Max® Manager, did not display “dL” but
does indicate:
“0”
1.
Remote device has not been set.
2.
The booth has not been connected to the remote system,
see Remote Connections.
a tanning time and the lamps have come on
1.
Delay time of T-Max® Manager has not been set.
2.
Delay time has expired and session has begun.
a tanning time but the lamps have not come on
Auto start function of T-Max® Manager has been turned off.
Press the timer button to turn on lamps.
Booth not tanning
1.
Clean booth, see Thorough Periodic Cleaning.
2.
Ensure supply voltage is between 208 and 230V AC.
3.
Replace lamps if lamp hours are greater than 700hrs.
4.
Replace acrylic.
Lamps fail to light and timer display is blank
1.
Make sure the unit is connected to a power source.
2.
Check source of AC power. Reset circuit breaker or replace
fuse.
Timer display changes to indicate a tanning time after the timer button
is pressed but lamps do not come on
1.
Bypass plug is not installed, see Electrical Connections.
2.
A bypass plug other than the one sent with your tanning
booth has been used.
3.
If remote is being used, other than T-Max® Manager, the
external timer may not be activated.
4.
Remote wiring is incorrect, see the instructions provided
with the remote interface kit.
Timer display continues to show a 0 after the timer button is pressed
1.
T-Max® Manager remote system has not yet been set.
2.
Booth address is not set correctly, see Remote Connections.
One or more lamps fail to light
1.
Check that lamp is installed correctly.
2.
Switch unlit lamp with a lamp that lights, if new lamp lights
and old lamp still does not, replace old lamp.
Problem
Troubleshooting
Solution
Problem
Troubleshooting
Solution
7
Replacing Lamps
To be assured of maximum tanning effectiveness, change lamps after
approximately 500 hours of use. Tanning will continue after this time
but at a slower rate. We recommend using the lamps specified below.
Use of uncertified lamps is a violation of Federal regulations and may
void your warranty.
1
Grasp a lamp at one end and at the middle, then turn the lamp a
quarter turn. The lamp may then be gently removed from its holder.
2
To reinstall lamp, insert pins on the ends of the lamp into the slots on
top of the lamp holder and turn the lamp a quarter turn.
The following lamps have been certified for use in this equipment:
Sunfire® Plus
FR71/160W
Hour Counter
This booth incorporates an ingenious hour counter function into the
timing circuitry. It allows the operator of the unit to monitor the hours
of use of the lamps, making it easy to determine when to change them.
You may also decide to use this function to monitor other time based
maintenance tasks.
To determine how many hours the unit has been in service (since the
last reset of the hour counter memory), first make sure the timer display
shows “0”. Then simply hold the stop button for three seconds.
The display will show two pairs of numbers which indicate the number
of hours of service, then return to “0”. (example: Display shows 08 then
54. This equals 854 hours.) NOTE: If the unit is connected to a TMax®
remote device, it may briefly lose communication with the remote. This
is normal.
To erase the indicated hours, disconnect power from the booth. Press
and hold the green timer button as you reconnect power. Release the
button after a few seconds.
