background image

66037A  2 07/19/11

WARNINg INFORMATION

This is the safety alert symbol. It is used to alert you 
to potential personal injury hazards. Obey all safety 
messages that follow this symbol to avoid possible 
injury or death.

             

 

IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING

BEFORE USING THIS DEVICE, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING 
PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.

It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsiblity of 
the device owner to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost 
or not legible, contact Sunex for replacements. If the operator is not fluent in English, the product and safety instructions shall be read 
to and discussed with the operator in the operator's native language by the purchaser/owner or his designee, making sure that the 
operator comprehends its contents.

THE NATURE OF HAZARDOUS SITUATIONS

The use of portable automotive lifting devices is subject to certain hazards that cannot be prevented by mechanical means, but only 
by the exercise of intelligence, care, and common sense. It is therefore essential to have owners and personnel involved in the use and 
operation of the equipment who are careful, competent, trained, and qualified in the safe operation of the equipment and its proper 
use. Examples of hazards are dropping, tipping or slipping of loads caused primarily by improperly securing loads, overloading, off-
centered loads, use on other than hard level surfaces, and using equipment for a purpose for which it was not designed.

METHODS TO AVOID HAZARDOUS SITUATIONS

  •  Read, study, understand and follow all instructions before operating this device.
  •  Inspect the jack before each use. Do not use jack if damaged, altered, modified, in poor condition, leaking hydraulic fluid, or 
    unstable due to loose or missing components. Make corrections before using.
  •  Lift only on areas of the vehicle as specified by the vehicle manufacturer.
  •  Wear eye protection that meets ANSI Z87.1 and OSHA standards.
  •  Do not use jack beyond its rated capacity.
  •  This is a lifting device only. Immediately after lifting, support the vehicle with jack stands capable of sustaining the load before  
    working on the vehicle.
  •  Use only on a hard level surface free from obstructions so the jack is free to reposition itself during lifting and lowering operations.
  •  Center load on saddle. Be sure setup is stable before working on vehicle.
  •  Do not move or dolly the vehicle while on the jack.
  •  Do not use saddle adapters or saddle extenders between the stock lifting saddle and the load.
  •  Do not use any adapters unless approved or supplied by Sunex.
  •  Always lower the jack slowly and carefully.
  •  Failure to heed these warnings may result in serious or fatal personal injury and/or property damage.

CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS

Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS,
MAINTENANCE INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS SITUATIONS
could cause accidents resulting in serious or fatal personal injury and/or property damage.

WARNING: Indicates a hazardous situation 
which, if not avoided, could result in death 
or serious injury.

WARNING

WARNING

WARNING

WARNING

Summary of Contents for 66037A




















Reviews: