background image

 

INSTALLATION INSTRUCTIONS 

Before Using Your Wine Cooler 

Remove the exterior and interior packing. 

Before  connecting  the  wine  cooler  to  the  power  source,  let  it  stand  upright  for 
approximately  2  hours.  This  will  reduce  the  possibility  of  a  malfunction  in  the 
cooling system from handling during transportation. 

Clean the interior surface with lukewarm water using a soft cloth. 

This cooler is specifically designed for the storage of wine 

– do not use it for other 

purposes. 

 

Installation of Your Wine Cooler 

This appliance is designed for free standing or built-in (fully recessed) installation. 
If free standing, the unit should have at least 4” of clearance at both sides, at the 
top and at the back to allow for adequate ventilation. If it is built-in, leave at least 
3/16” at both sides, 1/16” at the top and 2” at the rear. Be sure that airflow under 
the appliance is not blocked. 

Place your wine cooler on a floor that is strong enough to support it when it is fully 
loaded. To level your wine cooler, adjust the front leveling legs at the bottom of the 
unit. 

Locate  the  wine  cooler  away  from  direct  sunlight  and  sources  of  heat  (stove, 
heater,  radiator,  etc.).  Direct  sunlight  may  affect  the  acrylic  coating  and  heat 
sources  may  increase  electrical  consumption.Extremely  cold  ambient 
temperatures may also cause the unit to perform improperly. 

Avoid locating the unit in moist areas. 

Plug the wine cooler into an exclusive, properly installed and grounded wall outlet. 
Do not under any circumstances cut or remove the third (ground) prong from the 
power cord. Any questions concerning power and/or grounding should be directed 
toward a certified or authorized products service center. 

 

Reversing the Door Swing of Your Appliance 

This appliance has the capability of the door opening from either the left or right 
side. The unit is delivered to you with the door opening from the left side. Should 
you  desire  to  reverse  the  opening  direction,  please  follow  the  diagrams  and 
instructions on the following pages.   

 

Summary of Contents for SWC1987T

















Reviews: