Sullair EES LS25S Series Operator'S Manual And Parts List Download Page 24

Page: 24 / 66

Section 5
OPERATION

REJECTED AIR AND
RECLAIMED AIR DAMPERS
WILL NOT CYCLE

EXHAUST AIR COOLER THAN
DESIRED ROOM TEMPERA-
TURE

EXHAUST AIR WARMER THAN
DESIRED

OUTDOOR AIR DAMPER WILL
NOT OPEN OR FULLY OPEN
WHEN OUTDOOR AIR
CHANGEOVER SETTING IS
EXCEEDED

Defective Room Thermostat

Room Thermostat Improperly Wired

Room Thermostat Not Wired

Defective Damper Motor Actuator

Defective Outdoor Air Changeover
Switch in Temperature Controller

Improperly Set Outdoor Air
Changeover Switch

Defective Control Relay

Too Much Outdoor Air is Being Used to
Cool Compressor

Defective Mixed Air Temperature
Control

Improperly Set Mixed Air Temperature
Control Dial.

Improperly Adjusted Damper Linkage

Improperly Set Mixed Air Temperature
Control

Defective Mixed Air Temperature
Control

Insufficient Motor Actuator Travel

Improperly Designed Ductwork

Improperly Adjusted Damper Linkage

Defective Control Relay

Improperly Wired Relay or
Temperature Controller

Improperly Adjusted Motor Actuator
Travel

Defective Outdoor Air Changeover
Switch

Replace.

Rewire.

Wire.

Replace.

Check function and replace if neces-
sary.

Replace.

Adjust outdoor air minimum position
knob.

Replace.

Reset.

Readjust.

Reset.

Replace.

Adjust.

Redesign.

Readjust.

Replace.

Rewire.

Reset.

Replace.

5.5 TROUBLESHOOTING GUIDE

SYMPTOM

PROBABLE CAUSE

REMEDY

Summary of Contents for EES LS25S Series


































































Search results

Summary of Contents for EES LS25S Series

Reviews:

Related manuals for EES LS25S Series

Brands by name

Popular brands

Sullair EES LS25S Series, Operator'S Manual And Parts List

Search results

Summary of Contents for EES LS25S Series

Reviews:

Related manuals for EES LS25S Series

Brands by name

Popular brands