Sub-Zero 424FS Service Manual Download Page 37 | Manualshive

Page: 37 / 39

background image

Page 37

400 Series

400 Series

Component Access and Removal

6-37

Figure 6-85. Compartment Thermistor

Figure 6-86.

Evaporator Thermistor

Thermistor

Evap Cover

Screw

Slide

Grommet & Slot

Screw &
P- Clamp

Thermistor

Lower Light Strip Access and Removal (Model 430)

NOTE:

See ELECTRIC SHOCK WARNING at begin-

ning of this section.

The lower light strip is held in the channel of the light
strip housing, which attached to the control panel
assembly. To remove the lower light strip, you will first
need to remove the control panel assembly. Now, slide
the light strip out the end of the channel in the light strip
housing.

(See Figure 6-84)

Upper and Lower Compartment Thermistor Access
and Removal (Model 430)

The compartment thermistors are attached to the left
side wall with a Phillips-head screw, and the electrical
leads of the thermistors are routed through a notch in
the left-hand evaporator support cover and guarded by
a small rubber grommet.

(See Figure 6-85)

NOTE:

See ELECTRIC SHOCK WARNING at begin-

ning of this section.

To remove a compartment thermistor, first remove the
wine racks, all cabinet slides, cabinet slide spacers and
cabinet slide support spacers in the compartment.
Then, remove the evaporator fan cover mounting
screws, the evaporator fan cover and the lower evapo-
rator cover. Extract the evaporator support cover
mounting screws and pull the evaporator support cover
out while pushing the thermistor leads and grommet out
of the slot on the left-hand side. Then disconnect the
thermistor electrical leads.

Upper and Lower Evaporator Thermistor Access
and Removal (Model 430)

The evaporator thermistors are attached to the right
side evaporator brackets with a Phillips-head screw.

NOTE:

See ELECTRIC SHOCK WARNING at begin-

ning of this section.

To access an evaporator thermistor, first remove the
wine racks from the compartment. Then, remove the
evaporator fan cover mounting screws, the evaporator
fan cover and the evaporator cover. Extract the evapo-
rator support cover mounting screws from the right side
evaporator support cover and pull the evaporator sup-
port cover out. Extract the screw from the thermistor
and disconnect the thermistor electrical leads.

1

2

Control Panel Assy

Light Strip Housing

Light Strip

Figure 6-84. Lower Light Strip

«
...
35
36
37
38
39
»

Summary of Contents for 424FS








































Reviews:

No comments

Related manuals for 424FS

Brand: Vama Pages: 163

Brand: Scarlett Pages: 20

Brand: Linea 2000 Pages: 44

Brand: Küppersbusch Pages: 18

Brand: SEVERIN Pages: 34

Brand: Team Kalorik Pages: 40

Brand: Fac Pages: 62

Brand: Barton Pages: 6

Brand: nedis Pages: 36

Brand: Quirky Pages: 5

Brand: Rommelsbacher Pages: 20

MASTERCHEF PSC-150/SM

Brand: Sam Cook Pages: 34

Brand: Jenn-Air Pages: 16

Brand: Galaxy Equipment Pages: 4

Brand: Concept2 Pages: 24

Brand: Oursson Pages: 84

Brand: Eldom Pages: 36

Brand: German pool Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands