manualshive.com logo in svg

Stulz STULZ Ultra Series, Installation Operation & Maintenance

Share
Download
Stulz STULZ Ultra Series Installation Operation & Maintenance Download Page 32

STULZ Ultra-Series Humidifier Controller 

 

 

 

 

28  

(August, 

2013) 

 

 

   Conductivity Alarm 
 
Conduct.  Enable:No 
 Trip point:       20.0uS 
Pre-Alarm Enable:No 
 Trip point:        5.0uS 
Offset:             1.0°F 
Alarm Delay:       90 sec 

      Airflow Alarm 
 
High alarm Enable: No 
 Trip point:    1200.0 fpm 
Low alarm Enable: No 
 Trip point:     600.0 fpm 
Offset:           20.0 fpm 

   
 
Alarm Set 
 

CLOCK 

        

Version 

     Limit Humidity 
 
High alarm Enable:No 
 Trip point:     80.0%RH 
Low alarm Enable:No 
 Trip point:     40.0%RH 
Offset:           1.0°  

   Limit TemperatureHigh 
alarm Enable:No 
 Trip point:     80.0°F 
Low alarm Enable:No 
 Trip point:     40.0°F 
Offset:           1.0°F 
 

5.4.2.2  Control Humidity Alarms 

If the control humidity sensor is enabled, high and low 
alarms may be enabled and set to specific trip points. The 
offset behaves in the same manner as described in section 
5.4.2.1. It applies to both the high and low alarms. 

 

 

 

 

 

 

 

 

 

5.4.2.3  Limit Temperature Alarms 

If the limit temperature sensor is enabled, high and low 
alarms may be enabled and set to specific trip points. The 
offset behaves in the same manner as described in section 
5.4.2.1. It applies to both the high and low alarms.

 

 
 
 
 
 
 
 
 
 
 

5.4.2.4  Limit Humidity Alarms 

If the control humidity sensor is enabled, high and low 
alarms may be enabled and set to specific trip points. The 
offset behaves in the same manner as described in section 
5.4.2.1. It applies to both the high and low alarms. 

 

 

 

 

 

5.4.2.5 Conductivity 

Alarms 

If the conductivity sensor is enabled, a conductivity alarm 
can be enabled and the trip point in MicroSiemens can be 
adjusted. A Pre-conductivity alarm can be enabled and the 
trip point in MicroSiemens can be adjusted. 

The offset 

behaves in the same manner as described in section 
5.4.2.1. It applies to both the high and low alarms.

 

 
 
 
 
 
 
 
 
 
 
 
 

5.4.2.6 Airflow 

Alarm 

If the airflow sensor is enabled, high and low alarms may 
be enabled and set to specific trip points. The offset 
behaves in the same manner as described in section 
5.4.2.1. It applies to both the high and low alarms. 

 

 

 

 

 
 

 Clock 

Screen 

5.4.3

Enter the Clock menu to change trip points for common 
alarms on analog inputs. 

 

 
 
 
 
 
 
 
 
 

 

Control

 

   Control Humidity 
 
High alarm Enable:No 
 Trip point:     80.0%RH 
Low alarm Enable:No 
 Trip point:     30.0%RH 
Offset:           1.0%RH 
 

Summary of Contents for STULZ Ultra Series

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands