Stulz ClimaPac Compact Installation, Operation And Maintenance Manual Download Page 12 | Manualshive

Page: 12 / 29

background image

12

© STULZ Tecnivel – all rights reserved

EN/02.2021 Technical data subject to modifi cations

Air Handlers Units

ClimaPac Series

Vibration absorber must be installed according to the instructions of the manufacturer.

4.1.2 Space requirements for installation, maintenance and operation

The minimum space necessary for installation, operation and maintenance is one unit width on the
operator side, as indicated on the sketch below:

Space requirements.

If the unit is to be installed against a wall or back-to-back with another unit (see sketches below),
modules must be assembled together before positionning the unit in its fi nal location.

Installation against the wall.

«
...
10
11
12
13
14
...
»

Summary of Contents for ClimaPac Compact






























Reviews:

No comments

Related manuals for ClimaPac Compact

Brand: Daikin Pages: 34

Brand: Blue Summit Pages: 19

Brand: Allied Pages: 22

Brand: Salda Pages: 60

KOMFORT ERV D150

Brand: BLAUBERG Ventilatoren Pages: 16

KOMFORT Ultra D 105

Brand: BLAUBERG Ventilatoren Pages: 16

KOMFORT LE Series

Brand: BLAUBERG Ventilatoren Pages: 20

AVPTC**14 Series

Brand: Amana Pages: 32

Amana AVPTC 14 Series

Brand: Maytag Pages: 28

Brand: IBC Pages: 2

Brand: Rapid Pages: 162

CLCF Climate Changer

Brand: Trane Pages: 40

Brand: Trane Pages: 16

Brand: Carrier Pages: 44

Brand: ApenGroup Pages: 60

Modular L Smart

Brand: Daikin Pages: 90

Brand: York Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands