background image

Stuart Turner Ltd, Henley-on-Thames, Oxfordshire RG9 2AD ENGLAND

 Tel:   +44 (0) 1491 572655,      Fax:   +44 (0) 1491 573704

email:   [email protected]    web:  www.stuart-turner.co.uk

V.A.T. REG. No. 199 0987 92. Registered in England No. 88368. Registered Of

fi

 ce: Market Place, Henley-on-Thames

DECLARATION OF CONFORMITY

2006/42/EC

BS EN ISO 12100-1, BS EN ISO 12100-2, BS EN 809

2006/95/EC

BS EN 60335-1, BS EN 60335-2-41

2004/108/EC

BS EN 55014-1, BS EN 55014-2, BS EN 55022, BS EN 61000-3-2,  BS EN 61000-3-3, 

BS EN 61000-4-2,  BS EN 61000-4-3, BS EN 61000-4-4, BS EN 61000-4-5, BS EN 61000-4-6, 

BS EN 61000-4-11

1999/519/EC

BS EN 62233

2011/65/EU

 

IT IS HEREBY CERTIFIED THAT THE STUART ELECTRIC MOTOR DRIVEN PUMP AS  

 

 

SERIAL NUMBER BELOW, COMPLIES WITH THE ESSENTIAL REQUIREMENTS OF THE  

 

 

ABOVE E.E.C. DIRECTIVES.

 RESPONSIBLE 

PERSON

 

AND MANUFACTURER 

STUART TURNER LIMITED

  

HENLEY-ON-THAMES, 

OXFORDSHIRE

 

 

RG9 2AD  ENGLAND.

 Signed 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  

Business Development Director

Stuart Turner are an approved company to BS EN ISO 9001:2000

Issue No. 4413/2-01

Pt. No. 19547

Summary of Contents for PH35









Reviews: