background image

- 2 -

PRODUCT DESCRIPTION

Electric motor driven single stage end suction centrifugal pump.

APPLICATION

The range of centrifugal pumps is designed to pump clean fresh water.  Other clean, non 
aggressive, non explosive liquids with similar characteristics to water may be pumped.  
Consult Stuart Turner for advice on such applications.
The pumps can be used for pressure boosting, fluid transfer and distribution.  They are 
suitable for flooded suction applications.  Alternatively a maximum suction lift of    
4.6 metres is permitted when using a Stuart footvalve/strainer.

Inlet pressures to the pump and ambient temperatures must not exceed the values 
given in the technical specifications.

 

This pump set must not be used for any other application without the    

 

written consent of Stuart Turner Limited.

 

This pump must not be connected directly to the mains water supply.

 

This product should not be used for the supply of water to more than    

 

one dwelling (house, apartment, flat).

Please read installation details carefully as they are intended to ensure this product 
provides long, trouble free service.  Failure to install the unit in accordance with the 
installation instructions will lead to invalidation of the warranty.

STORAGE

If this product is not to be installed immediately on receipt, ensure that it is stored in a dry, 
frost and vibration free location in its original packaging.

CONTENTS 

Page

Checklist  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electrical Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Commissioning  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Technical Specifi cation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

CHECKLIST

Your product may vary slightly from the picture above.

Item Description

Qty Item Description

Qty

Pump

1

A

A

Fig. 1

G 1 Outlet

Priming
Plug

G 1 Inlet

IMPORTANT:  With the pump 
removed from its packaging 
check for any damage prior to 
installation.  If any damage is 
found contact Stuart Turner Ltd 
within 24 hours of receipt.

Summary of Contents for PH35









Reviews: