Stuart Turner supersub 230a Installation, Operation & Maintanance Manual Download Page 10

- 10 -

Cont ...

4.22 

Supply Cord Extension (Pump)

:  The pumps are fitted with a supply cord  

 

 

suitable for outdoor and underwater use.  The cord specification is as follows:-

Pump Type

Cord Type

Cord Length (m)

Supersub 230A

HO5RN-F3 G 0.75 mm²

10

Supervort 140A

HO5RN-F3 G 0.75 mm²

10

Supervort 240A

HO5RN-F3 G 1 mm²

10

 

If an extension cord is necessary a cord of the proper type and rating must be    

 used.
 

In general for 230 volt pumps on distances up to 40 metres (inclusive of original   

 

cord length) the same specification cord as fitted to the pump can be used.  For  

 

distances above 40 metres a larger cord size may be required due to voltage  

 

 

drop and advice must be obtained based upon installation details.

 

Any connectors or junction boxes must be specifically suited for outdoor use    

 

and installed in accordance with manufacturers instructions.

 

Any cable routed underground must be protected to local standards.

4.23 

Float Switch Cord Extension (applicable models only): 

The float switch    

 

cord cannot be extended.

Summary of Contents for supersub 230a

















Reviews: