background image

- 3 -

Cont ...

WARNINGS:

 

z

This pump set must not be used for any other    

 

  application without the written consent of Stuart  

 

  Turner Limited and in particular, must not be    

 

  connected directly to the mains water supply.

 

z

This appliance can be used by children aged from  

 

  8 years and above and persons with reduced    

 

  physical, sensory or mental capabilities or lack of  

 

  experience and knowledge if they have been given    

  supervision or instruction concerning use of the  

 

  appliance in a safe way and understand the hazards    

 involved. 

 

z

Children must not play with the appliance.

 

z

Cleaning and user maintenance shall not be made by  

  children without supervision.

 

z

Maximum head (closed valve) PH 35 TS-30 metres,    

  PH 45 TS-42 metres, PH 35 ES-30 metres,  

 

 

  PH 45 ES-42 metres.

 

z

The motor casing can become very hot under normal  

  operating conditions. Care must be taken to ensure it  

  cannot be touched during operation.

 

z

The electrical installation must be carried out    

 

  in accordance with the current national electrical  

 

 regulations.

 

z

The electrical installation must be installed by a  

 

  qualified person.

 

z

In the interests of electrical safety a 30 mA residual    

  current device (R.C.D. not supplied) should be   

 

  installed in the supply circuit.  This may be part of a    

  consumer unit or a separate unit.

 

z

Before starting work on the electrical supply ensure    

  power supply is isolated.

 

z

DO NOT allow the supply cord to contact hot    

 

  surfaces, including the motor shell, pump body or    

  pipework.  The cord should be safely routed and  

 

  secured by cable clips.

Summary of Contents for PH 45 TS S

















Reviews: