background image

- 14 -

8  YOUR 2 YEAR GUARANTEE

Congratulations on purchasing a Stuart Turner pump. 

We are confident this pump will provide many years of trouble free service as all 

our products are manufactured to the very highest standard. 

All Stuart Pumps are guaranteed to be free from defects in materials or 

workmanship for 2 years from the date of purchase.  

Within the guarantee period we will repair, free of charge, any defects in the pump 

resulting from faults in material or workmanship, repairing or exchanging the whole 

unit as we may reasonably decide. 

Not covered by this guarantee: Damage arising from incorrect installation, 

improper use, unauthorised repair, normal wear and tear and defects which have a 

negligible effect on the value or operation of the pump. 

Reasonable evidence must be supplied that the product has been purchased within 

the guarantee term prior to the date of claim (such as proof of purchase or the 

pump serial number). 

This guarantee is in addition to your statutory rights as a consumer.  If you are 

in any doubt as to these rights, please contact your local Trading Standards 

Department. 

In the event of a claim please telephone 

‘TechAssist’

 or return the pump and 

flexible hoses with the accessories removed e.g  pipes etc. If you have any doubt 

about removing a pump, please consult a professional.

+44 (0) 800 31 969 80

Proof of purchase should accompany the returned unit to avoid delay in 

investigation and dealing with your claim. 

You should obtain appropriate insurance cover for any loss or damage which is not 

covered by Stuart Turner Ltd in this provision.

Please record here for your records.

TYPE NO.

SERIAL NO.

DATE PURCHASED

Summary of Contents for PH 45 TS S

















Reviews: