background image

Stuart Turner Ltd, Henley-on-Thames, Oxfordshire RG9 2AD ENGLAND

 Tel:   +44 (0) 1491 572655,      Fax:   +44 (0) 1491 573704

[email protected]    www.stuart-turner.co.uk

DECLARATION OF CONFORMITY

Machinery Directive - 2006/42/EC

BS EN 12100, BS EN 809

Low Voltage Directive - 2014/35/EU

BS EN 60335-1, BS EN 60335-2-41

EMC Directive - 2014/30/EU

BS EN 55014-1, BS EN 55014-2, BS EN 61000-3-2,  BS EN 61000-3-3, 

BS EN 61000-4-2,  BS EN 61000-4-3, BS EN 61000-4-4, BS EN 61000-4-5, BS EN 61000-4-6, 

BS EN 61000-4-11

EMF Directive - 1999/519/EC

BS EN 62233

RoHs Directive - 2011/65/EU

WEEE Directive - 2012/19/EU

 

IT IS HEREBY CERTIFIED THAT THE STUART ELECTRIC MOTOR DRIVEN PUMP AS SERIAL  

 

 

NUMBER BELOW, COMPLIES WITH THE ESSENTIAL REQUIREMENTS OF THE ABOVE E.E.C.  

 

 DIRECTIVES.

 

RESPONSIBLE PERSON

 

AND MANUFACTURER 

STUART TURNER LIMITED

 

 

HENLEY-ON-THAMES, OXFORDSHIRE

 

 

RG9 2AD  ENGLAND.

 Signed   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Engineering Manager

Stuart Turner are an approved company to BS EN ISO 9001:2015

Issue No. 4219/4-01

Pt. No. 19097

Summary of Contents for PH 45 TS S

















Reviews: