Stuart Turner 46601 Installation, Operation & Maintenance Instructions Manual Download Page 18

- 18 -

Cont ...

9  THE MONSOON EXTRA GUARANTEE

Congratulations on purchasing a Stuart Turner pump. 
We are confident this pump will provide many years of trouble free service as all our 
products are manufactured to the very highest standard. 
All Monsoon Extra pumps are guaranteed to be free from defects in materials or 
workmanship for 2 years from the date of purchase.  

EXTEND YOUR PUMP GUARANTEE

Register your pump details on-line now (within 30 days of date of purchase) and the 
standard 2 year guarantee will be extended 

FREE

 of charge for a further one year.  

www.stuart-turner.co.uk 

If you do not have on-line access or would like us to help you register your pump then 
simply call our 

‘PumpAssist’

 helpline on 

0844 98 000 97

.

Please note that to validate your extended warranty we will require the following 
information:  
 

1.  Full pump serial number (including last 3 digits) which can be found on the  

 

 

 

pump rating label and the back page of the installation instructions. 

 

2.  Your name/address/telephone/e-mail.  

 

3.  The date of installation.

Within the guarantee period we will repair, free of charge, any defects in the pump 
resulting from faults in material or workmanship, repairing or exchanging the whole unit 
as we may reasonably decide. 
Not covered by this guarantee: Damage arising from incorrect installation, improper 
use, unauthorised repair, normal wear and tear and defects which have a negligible 
effect on the value or operation of the pump. 

Reasonable evidence must be supplied that the product has been purchased within the 
guarantee term prior to the date of claim (such as proof of purchase or the pump serial 
number). 

This guarantee is in addition to your statutory rights as a consumer.  If you are in any 
doubt as to these rights, please contact your local Trading Standards Department. 

In the event of a claim please telephone 

‘PumpAssist’

 or return the pump with the 

accessories removed e.g  pipes etc. If you have any doubt about removing a pump, 
please consult a professional.

0844 98 000 97

Summary of Contents for 46601





















Reviews: