8. Disconnect the keypad/display cable. Remove and save the keypad display.
9. Remove the footboard from the product.
10. Using a #2 Phillips screwdriver, remove and save the two screws that secure the footboard main cable to the bottom of
the footboard.
11. Remove the footboard main cable from the footboard and discard.
12. Reverse steps to reinstall.
13. Verify proper operation of the product before you return it to service.
F
Fo
ow
wlle
err a
accttu
ua
atto
orr rre
ep
plla
acce
em
me
en
ntt
T
To
oo
ollss rre
eq
qu
uiirre
ed
d::
•
Needle nose pliers
•
Small flat screwdriver
•
Syn-Tech grease (3000-200-719)
P
Prro
occe
ed
du
urre
e::
1. Raise the product to the highest height position.
2. On the footboard control panel, press E
En
ntte
err to access the S
Se
ettttiin
ng
gss menu.
3. Highlight S
Sh
hu
uttd
do
ow
wn
n and press E
En
ntte
err.
4. Unplug the power cord from the wall outlet.
5. Push down on the brake pedal to apply the brake.
6. Raise both head end siderails to the up and locked position.
7. Pull the CPR release handle to lower the fowler down.
8. Using needle nose pliers, remove both rue ring retaining clips from the clevis pins that attach the actuator to the litter
weldment and fowler weldment.
9. While supporting the actuator with one hand, remove the head end clevis pin and then lower the actuator down.
N
No
otte
e -- Apply a thin coat of Syn-Tech grease to the clevis pin when you reinstall.
10. Using a small flat screwdriver, unlock the gray CPR pull retainer from the red CPR pull to loosen the CPR pull retainer.
11. Using a small flat screwdriver, remove the gray CPR pull retainer from the red CPR pull. A white spacer between the
CPR pull and the CPR cable retaining bracket will fall out. Save the white spacer.
12. Remove the CPR cables from the CPR cable retaining bracket.
13. Using a small flat screwdriver, release the retaining ring from the power and sensor cable quick connects and
disconnect the cables from the actuator. When re-connecting the cables, fully seat and lock the cable quick connector
retaining ring.
14. While supporting the actuator with one hand, remove the foot end clevis pin and then lower the actuator down.
N
No
otte
e -- Apply a thin coat of Syn-Tech grease to the clevis pin when you reinstall.
15. Reverse steps to reinstall.
16. Verify proper operation of the product before you return it to service.
G
Ga
attcch
h a
accttu
ua
atto
orr rre
ep
plla
acce
em
me
en
ntt
T
To
oo
ollss rre
eq
qu
uiirre
ed
d::
•
Needle nose pliers
•
Small flat screwdriver
5900-009-002 Rev A.0
29
EN
Summary of Contents for MV3 5900
