Stryker LIFEPAK 15 Pocket Manual Download Page 30 | Manualshive

Page: 30 / 30

Stryker LIFEPAK 15 Pocket Manual Download Page 30

©2018 Physio-Control, Inc. All names herein are trademarks
or registered trademarks of their respective owners. Masimo,
the Radical logo, Rainbow and SET are registered trademarks
of Masimo Corporation.
GDR 3307601_D

Refer to operating instructions for complete
directions for use indications, contraindications,
warnings, cautions, and potential adverse events.
Physio-Control is now part of Stryker.
For further information, please contact Physio-
Control at 800.442.1142 (U.S.), 800.668.8323 (Canada)
or visit our website at www.physio-control.com

Physio-Control, Inc.,

11811 Willows Road NE, Redmond, WA 98052 USA

Physio-Control Headquarters

11811 Willows Road NE
Redmond, WA 98052 USA
Tel 425 867 4000
www.physio-control.com

Customer Support

P. O. Box 97006
Redmond, WA 98073
Toll free 800 442 1142
Fax 800 426 8049

Physio-Control Canada

Physio-Control Canada
Sales, Ltd.
45 Innovation Drive
Hamilton, ON
L9H 7L8
Canada
Toll free 800 668 8323
Fax 877 247 7925

«
...
28
29
30

Summary of Contents for LIFEPAK 15































Reviews:

No comments