manualshive.com logo in svg

Stryker LIFEPAK 15, Pocket Manual, Page: 29 / 30

Share
Download
Stryker LIFEPAK 15 Pocket Manual Download Page 29

Page 27

Troubleshooting Tips

For a complete list of troubleshooting tips, please 

consult the LIFEPAK 15 Operating Instructions

LIFEPAK 15 

Monitor/Defibrillator

Temperature

Observation

Action

Screen remains blank

Temp outside range of 24.8° and 

45.2° C (76.6° and 113.4° F)

CHECK SENSOR message 

appears and value is (---)

• Temp outside of range, the probe 

is dislodged, not connected or the 

cable not connected to the monitor

• Check that probe is properly 

positioned 

CHECK SENSOR message 

appears while value is 

displayed

Temp probe is dislodged and value 

is below 31° C (87.8° F) or above 

41.0° C (105.8° F)

TEMP: ACCURACY 

OUTSIDE LIMITS message 

appears and value is XXX

• Temperature module is not 

calibrated or accuracy check failed

• Turn device off then on again. If 

problem persists, contact qualified 

service personnel.

NOTE:

   The temperature probe may require 3 minutes  

to equilibrate after placement on the patient  

monitoring site.

Summary of Contents for LIFEPAK 15































Reviews:

No comments