manualshive.com logo in svg

Stryker Medical 1020, Maintenance Manual

Share
Download
Stryker Medical 1020 Maintenance Manual Download Page 13

Service Information

12

HYDRAULIC TROUBLESHOOTING

NOTE
Be sure the pedal linkage has been adjusted properly before beginning service on the jacks (see page 8
or page 9).

PROBLEM/SYMPTOM

SOLUTION

Jack will not raise to full height.

Add hydraulic fluid (see p.13). Check for leaks.

Jack will not hold in raised position.

Close the needle valve completely. If the jack
holds, replace valve #1 (see p. 15). If the jack
does not hold, replace valve #2 (see p. 16).

Jack will not pump up and the jack actuator rod

does not

 move.

Close the needle valve. If the jack will now pump
up, replace valve #1. If the jack still will not pump
up after closing the needle valve, replace valve #3
(see p. 16).

Jack will not pump up but the jack actuator rod

does

 move when the pump pedal is activated.

Replace valve #2 (see p. 16).

Jack will not pump up and the jack actuator rod
may or may not move.

Remove excess air (vacuum) in system (see p.
13).

Contact Stryker technical service at 1–800–327–0770 for further assistance.

Summary of Contents for 1020






























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands