manualshive.com logo in svg

Struers LaboForce-100, Instruction Manual

Share
Download
Struers LaboForce-100 Instruction Manual Download Page 22

Note

Do not use a dry cloth as the surfaces are not scratch resistant.

Note

Do not use acetone, benzol or similar solvents.

If the machine is not to be used for a longer period of time

•

Clean the machine and all accessories thoroughly.

7.2

Daily

•

Clean all accessible surfaces with a soft, damp cloth.

7.3

Weekly

•

Clean the control panel with a soft damp cloth and common household detergents.

7.3.1

LaboForce-100 - the specimen mover head

Cleaning

LaboForce-100 is equipped with a function for cleaning the feet that apply the force on the specimens
and also for cleaning the lock that secures the specimen mover plate for single specimens.

The force on the pressure feet is generated by friction pins held in place by the screws in the spring
housing.

Clean the pressure feet and pistons applying the force on the specimens and specimen holder.

Procedure

1.

Press the release outlet valve to drain the water/oil filter. See the section

LaboForce-100 - Emptying the water/oil filter ►23

.

2.

From the

Main menu

select

Maintenance

>

Cleaning of specimen mover

head

.

3.

Press

F1

to activate one of the functions shown.

Note

Never force any of the movements. If the components do not move as they should,
contact Struers Service.

–

Lower feet

The pistons can be cleaned or lubricated.

–

Raise feet

Moves the feet back into operating position.

22

LaboForce-100

7   Maintenance and service

Summary of Contents for LaboForce-100



































Reviews:

No comments

Brands by name

Popular brands

Load more brands