manualshive.com logo in svg

Struers LaboForce-100, Instruction Manual

Share
Download
Struers LaboForce-100 Instruction Manual Download Page 21

Button

Function

Water

Manual override

•

Press the button to apply water. Water is applied when no process is running.

•

Press the button again to stop applying water. Water switches off automatically
after 5 minutes.

Abrasive

This function is only active when dosing units are installed.

•

Manual override: Press this button to apply diamond suspension from the doser
bottle.

Lubricant

This function is only active when dosing units are installed.

•

Manual override: Press this button to apply lubricant from the doser bottle.

Start

•

Starts the preparation process.

Stop

•

Stops the preparation process.

Escape

•

Press this button to return to the previous screen or to cancel functions/changes.

A

Turn/push knob
knob

The Turn/push knob knob

•

Turn the

Turn/push knob

knob to move the focus on the screen

and change steps and setting. Press to toggle when only 2
options are available.

•

Press the

Turn/push knob

knob to select a function or save a

selected setting.

7

Maintenance and service

Technical questions and spare parts

If you have technical questions or when you order spare parts, state serial number and
voltage/frequency. The serial number and the voltage are stated on the type plate of the machine.

7.1

General cleaning

To ensure a longer lifetime for your machine, Struers strongly recommends regular cleaning.

7   Maintenance and service

LaboForce-100

21

Summary of Contents for LaboForce-100



































Reviews:

No comments

Brands by name

Popular brands

Load more brands