12
PART 1 • English
7.3 Channel Search
To access the menu press MEnU and select
Channel
Search
. It contains two options:
Installation
and
DB
(
Data
Base
)
Management
. Select an option and press ok to enter it. Press EXIT to exit the menu.
7.3.1 Installation
7.3.1.1 Satellite Selection
Use
pq
buttons to highlight the satellite your dish is aimed at. Its antenna settings will be shown at the
right side. You can enter the right side with
tu
buttons and return to the satellite list with EXIT.
7.3.1.2 Configure the antenna settings for selected satellite
LNB Type:
Press
tu
or
OK
to show the list of LNB Types which is shown as frequencies
of local oscillator. You also can enter frequency by User Single, User Dual at
bottom of the list. Default is set a Universal LNB (09750/10600) – the most
used on the market.
LNB Power:
Press
tu
to set the LNB power. 13/18V is the setting for a Universal LNB.
22 kHz:
Press
tu
to switch on or off the 22KHz oscillator signal.
Auto
is the setting for
a Universal LNB.
Toneburst:
to enable or disable the toneburst switcher if available.
DiSEqC1.0:
to select the right port from up to 4 (if available) for the right LNB.
DiSEqC1.1:
to select the right port from up to 16 (if available) for the right LNB.
Motor:
if using a motor press
tu
to select between
DiSEqC1
.
2
or
GOTOX
depending
of motor type. Then Press ok to show the menu to set position or gREEn
for location.
DiSEqC1.2:
Move the motor to the right position for locking the signal like explained below.
Move Continue:
Press
tu
for moving
West
/
East
. It will keep moving as long as the button is
hold pressed. Once pressing will move in 1°step.
Move Step(1):
Press
tu
for moving
West
/
East
in 0.3° step.
Store Position:
to store the current motor position for selected satellite.
Goto Reference:
to go to the reference 0° position.
GOTO X:
Set your location coordinates. Main German locations are preinstalled. Press
tu
to select. If
Manual
selected use
tu
, UP/DoWn and nUMERIC buttons
to enter the right position. By pressing ok position gets stored and the motor
moves automatically towards selected satellite.
Set Limit for DiSEqC1.2 and GOTO X options:
For Move Continue, Move Step(1) and Goto Reference please see explanation above.
Set West Limit:
to store the current motor position as West limit.
Set East Limit:
to store the current motor position as East limit.
Disable Limit:
to disable West and East limits
7.3.1.3 Channel Scan
Automatic Scan
Single Satellite Scan:
Press blUE for
Scan
. A window with scanning settings will be displayed.
Scan Mode:
Press
tu
to select
Default
,
Blind
Scan
or
NetWork
.
Default
:
All in the memory stored transponders will be scanned.
Blind
Scan
:
Slow scan in 2 MHz step. It first scans the whole frequency band to get the
transponders which can be locked. After gathering all transponders, it scans
the transponders one by one to get the programs.
NetWork
:
Network search will be performed – when a Network information is
broadcasted new switched transponders will be found and stored.
Crypted:
Press
tu
to select
All
Channels
(scrambled and free) or
FTA
Channels
(free to air);
Service Type:
Press
tu
to select
ALL
,
DTV
or
Radio
.
Summary of Contents for SRT 7000
Page 1: ...User Manual Digital High Definition Satellite Receiver SRT 7000 Picture similar ...
Page 2: ......
Page 3: ......