Strata ADVANCEMIG 255 Operating Instructions Manual Download Page 2

Page: 2 / 24

www.strata.co.nz

EZIMIG 205 / ADVANCEMIG 255

Contents

Specifications................................................................4

Standard Accessories.............................................................4

Getting to Know Your Machine................................................5

MMA Welding.........................................................................7

Installation and Setup for MMA (Stick Welding)......................7

MIG Welding...........................................................................8

Installation and Setup for MIG Welding...................................8

EZIMIG 205 Synergic MIG Program Chart...............................9

ADVANCEMIG 255 Synergic MIG Program Chart....................9

MIG Welding Manual Selection.............................................11

Save and Recall User Set Welding Parameters.......................13

Gasless Welding Setip and Operation....................................13

Gas Shielded Welding Setup and Operation...........................13

Lift TIG Setup and Operation................................................14

Spool Gun Setup and Operation.............................................14

Care & Maintenance..............................................................15

Storing the Welder................................................................16

Safety................................................................................17

Notes.................................................................................22

Warranty...............................................................................23

Summary of Contents for ADVANCEMIG 255

























Search results

Summary of Contents for ADVANCEMIG 255

Reviews:

Related manuals for ADVANCEMIG 255

Brands by name

Popular brands

Strata ADVANCEMIG 255, Operating Instructions Manual

Search results

Summary of Contents for ADVANCEMIG 255

Reviews:

Related manuals for ADVANCEMIG 255

Brands by name

Popular brands