STORK TRONIC 900340.012 Wiring Diagram Download Page 29

Page: 29 / 29

Order no. 900340.012

V1.54

Page 29

Technical data of ST603-QN1LAR.112

Measuring inputs

F1:

Resistance sensor PTC (KTY81-121)

F2:

Resistance sensor PTC (KTY81-121)

F3:

Resistance sensor PTC (KTY81-121) (optional linear input, current 4...20 mA)

Measuring range:

PTC -50°C...+150 °C

Measuring accuracy: ±0,5K ± 0,5 % at 25°C, without sensor

Outputs

K1:

Relay, 16(6)A 250V~, normally-open contact

Please note:

Relay K1 is connected in series with input E1

(high pressure switch) Relay K1 can only be energized if E1 is closed!

K2:

Relay, 16(6) A 250V~, normally-open contact

K3:

Relay, 16(2.2) A 250V~, normally-open contact

K4:

Relay, 8(1.5) A 250V~, change-over contact

ST-Bus communication interface

Interface driver: RS485, galvanically not separated

The network has to be installed in lines topology and terminated with a 120 Ohm resistance on each side.

In case of networking always connect port “A” with port “A” and port “B” with port “B”. Crossing over is not

permissible!

Power supply

230V~ 50/60Hz, power consumption max. 20VA

Connectors

Screw terminals

4-pole, spacing 5.00mm, for cables up to 2.5 mm²

4-pole, spacing 7.50mm, for cables up to 2.5 mm²

3-pole, spacing 5.00mm, for cables up to 2.5 mm²

13-pole, Raster 3.50mm, for cables up to 0.5 mm²

Ambient conditions

Storage temperature:

–20°C...+70°C

Operating temperature: 0...55°C

Relative humidity:

max. 75 %, without dew

Weight

Ca. 800g

Enclosure

IP65 with appropriate connection cables

Installation data

Wall mounted housing with cable gland

External dimension

186mm x 161mm x 121mm

Cable connections

1x screwing M12 for round cables with diameter 1.0...5.0mm

2x screwing M16 for round cables with diameter 4.5...10.0mm

1x screwing M20 for round cables with diameter 7...13mm

Summary of Contents for 900340.012






























Search results

Summary of Contents for 900340.012

Reviews:

Related manuals for 900340.012

Brands by name

Popular brands

STORK TRONIC 900340.012, Wiring Diagram

Search results

Summary of Contents for 900340.012

Reviews:

Related manuals for 900340.012

Brands by name

Popular brands