background image

1 x 1770 x 780mm door sheet.
2 x 1770mm “U” channels.
2 x 780mm “U” channels.
1 x 310mm door plate.
Hinges.
Door bracing.

If you choose to vary from these instructions 

your warranty will be impaired.

2

1. 

Attach the 780mm “U” channels 

J

 to 

the top and bottom of the door sheet 

A

 at the centre ribs only.

2. 

Attach the 1770mm “U” channels 

H

 to 

the door sheet 

A

 through the top and 

bottom channels 

J

 at the four corners.

3. 

Attach the door plate 

M

 in the centre of 

the door sheet, slipping it under the two 

side “U” channels and fixing it to the 

sheet ribs and the side “U” channels.

4. 

Attach the hinges 

N

 approx 150mm 

from the top and bottom of the door 

through the “U” channels. The fixings 

should be centred on the side “U” 

channels.

5. 

Turn the door over and fix the four 

corners through all the “U” channels 

and fit the door bracing from the bottom 

corner to the opposite centre to the top 

corner.  (step 2 below).

Step 1: 

Door Assembly

A

A

N

O

H

H

H

J

J

J

M

You will need:

1. 

Attach the first “Z” door jamb 

L

 to the 

740mm sheet 

B

 on the rib with the 

narrow pan. Attach the other “Z” door 

jamb to the 740mm sheet 

B

.

2. 

Lay the premade door face down on the 

740mm sheet 

B

 approx 30mm up from 

the bottom and down from the top.

3. 

Check the door is centralised on the 

sheet (top and bottom). Fix the hinges 

through the side of  the “Z” door jamb 

L

, raising the door about 4mm off the 

"Z" door jamb.

Step 2: 

Hanging the 

door

B

L

2 x 1830 x 740mm sheet.
1830mm “Z” door jambs.

You will need:

M

N

30mm

4mm

gap

Narrow pan

If you need advice, call us FREE on 0800 807 433  

or email us at [email protected]

150mm

Hinges should 
protrude over the 
top of the channel

Summary of Contents for rite 5









Reviews: