background image

If you choose to vary from these instructions 

your warranty will be impaired.

4

1. 

Join the three sheets 

C

 together with 2 fixings 

through the overlapping ribs, making sure the ends of 

the sheets are flush.

2. 

Cap the sheeting with the 2255mm “U” channels 

F

.

3. 

Fix the channels through the end ribs and  

every second rib in between.

4. 

Make sure you put at least one fixing per  

sheet up through the underside of the  

channel into the pan of the sheet.

1. 

Cap the sloping sheets 

E

 with the “U” channels  

G

.

2. 

Make a cut in the flanges only at (1145mm) the 

centre of the 

 

G

 2290mm top channels

3. 

Cap the sheeting with the 2255mm “U” channels  

 

G

 

4. 

Slip the gable 

 

Q

 plate under the channel at the top 

and fix to sheeting at the shown side.

5. 

Fix the channels at every 2nd rib and through gable 

plate into the sheeting ribs.

6. 

3 fixings up underneath through channel into pan of 

sheet

7. 

Perform the same at the other end. 

1. 

Join the sheets 

D

 together, same as the back.

2. 

Cap the sheeting with the 2255mm “U” channels 

F

.

3. 

Fix the channels at every second rib but not the corners 

at this stage.

4. 

Place the short flange of the first “L” flashing 

K

 on 

top of the rib at one end. Make sure the ends are flush 

with the sheeting (diagram 1) and put one fixing in the 

centre to hold the “L” flashing. Fix the corners through 

the channels and one more between the corner and the 

centre fixing.

5. 

Perform the same at the other end.

6. 

Fit the ridge beam 

P

 to 1 roof panel only. Fix through the 

ends and up through the internal flange on the underside.

Step 4:

Back wall

Step 5: 

Roof

Step 6: 

End walls

C

F

F

F

3 x 

1830 x 

780mm sheets. 

2 x 2255mm “U” channels.

D

E

F

G

Q

K

P

6 x 

1200 x 

780mm sheets. 

4 x 2255mm “U” channels.
4 x 1200mm “L” flashings.
1 x 2280mm long ridge beam

3 x gable angle cut sheets per side
2 x Channels per side
2 x Gable plates

You will need:

You will need:

You will need:

Channels 
will end 
15-20mm 
short at 
tops of end 
walls and 
10-15mm at 
bottoms.

Tip

Put extra fixings in 

for high wind areas, 

particularly on the 

underside.

C

If you need advice, call us FREE on 0800 807 433  

or email us at [email protected]

D

F

F

P

K

K

diagram 1

Tip

Bend pan ends 

up in high wind 

areas, see DVD.

Summary of Contents for rite 5









Reviews: