Stone SAW DEVIL CS1 Operator'S Manual Download Page 8

- 8 -

Health and Safety

Ear protection required when operating this equipment.

This notation appears before warnings in the text.  It means that the
step which follows must be carried out to avoid the possibility of
personal injury or death.  These warnings are intended to help the
technician avoid any potential hazards encountered in the normal
service procedures.  We strongly recommend that the reader takes
advantage of the information provided to prevent personal injury or
injury to others.

USE COMMON SENSE WHEN HANDLING FUELS

Transport and handle fuel only when contained in approved safety
container.

Do not smoke when refueling or during any other fuel handling opera-
tion.

Do not refuel while the engine is running or while it is still hot.

If fuel is spilled during refueling, wipe it off from the engine immediately
and discard the rag in a safe place.

Do not operate the equipment if fuel or oil leaks exist - repair immedi-
ately.

Never operate this equipment in an explosive atmosphere.

Before using this equipment, study this entire
manual to become familiar with its operation.  Do
not allow untrained or unauthorized personnel,
especially children, to operate this equipment.
Use only factory authorized parts for service.

When warning decals are destroyed or missing,
contact the Manufacturer immediately at 1-800-
888-9926 for replacement.  For the safety of your-
self and others, it is imperative that the following
rules are observed.  Failure to do so may result in
serious injury or death.

Safety Precautions

Summary of Contents for SAW DEVIL CS1

































Reviews: