Stone SAW DEVIL CS1 Operator'S Manual Download Page 6

L i m i t e d    W a r r a n t y

The Manufacturer warrants that products manufactured shall be free from defects in material and
workmanship that develop under normal use for a period of 90 days for concrete vibrators and electric
pumps, one year for Rhino

®

, Bulldog

®

, Wolfpac Rollers

™

, trowels, Stompers

®

, saws, forward plates,

engine  powered  pumps,  and  6 months for all other products from the date of shipment.  The foregoing
shall be the exclusive remedy of the buyer and the exclusive liability of the Manufacturer.  Our warranty
excludes normal replaceable wear items, i.e. gaskets, wear plates, seals, O-rings, V-belts, drive chains,
clutches, etc.  Any equipment, part or product which is furnished by the Manufacturer but manufactured by
another, bears only the warranty given by such other manufacturer.  (The Manufacturer extends the warranty
period to “Lifetime” for the drum bearings and seals for the mortar mixers, and agrees to furnish, free of
charge, the bearings and seals only upon receipt of the defective parts. The warranty is two years for
eccentric bearings on the forward plate compactors, mortar and plaster mixer drums, trowel gearboxes
and five years on the Bulldog trench roller eccentric bearings.)  A  Warranty Evaluation Form must accompany
all defective parts.  Warranty is voided by product abuse, alterations, and use of equipment in applications
for which it was not intended, use of non-manufacturer parts, or failure to follow documented service
instructions.  The foregoing warranty is exclusive of all other  warranties whether written or oral, expressed
or implied.  No warranty of merchantability or fitness for a particular purpose shall apply.  The agents,
dealer and employees of Manufacturer are not authorized to make modification to this warranty, or additional
warranties binding on Manufacturer.  Therefore, additional statements, whether oral or written, do not
constitute warranty and should not be relied upon.

The Manufacturer’s sole responsibility for any breach of the foregoing provision of this contract, with respect
to any product or part not conforming to the Warranty or the description herein contained, is at its option (a)
to repair, replace or refund such product or parts upon the prepaid return thereof to location designated
specifically by the Manufacturer.  Product returns not shipped prepaid or on an economical transportation
basis will be refused (b) as an alternative to the foregoing modes of settlement - the Manufacturer’s dealer
to repair defective units with reimbursement for expenses, except labor, and be reviewed with the
Manufacturer prior to repair.  A Warranty Evaluation Form must accompany all warranty claims.

Except as set forth hereinabove and without limitation of the above, there are no warranties or other
affirmations which extends beyond the description of the products and the fact hereof, or as to operational
efficiency, product reliability or maintainability or compatibility with products furnished by others.  In no
event whether as a result of breach of contract or warranty or alleged negligence, shall the Manufacturer
be liable for special or consequential damages including but not limited to: Loss of profits or revenues, loss
of use of the product or any associated product, cost of capital, cost of substitute products, facilities or
services or claims of customers.

No claim will be allowed for products lost or damaged in transit.  Such claims should be filed with the carrier
within fifteen days.

Effective April 1, 1998.

4/98 P/N 51018

Stone Construction Equipment, Inc.

32 East Main Street, P. O. Box 150

Honeoye, NY 14471-0150

Bred Tough, Born To Work. The

Way It Ought To Be.

Phone:  1-800-888-9926  •  1-716-229-5141

Fax:  1-716-229-2363

www.stone-equip.com   •  e-mail: [email protected]

Summary of Contents for SAW DEVIL CS1

































Reviews: