background image

20

AFTER SALES SUPPORT

1300 886 649

[email protected]

AUS

MODEL: STR-WPTL6K   PRODUCT CODE: 62971  11/2018

Instructions (Cont.)

Delayed washing 

This washing machine has a 0–24 hour delay start function which you can set to 
determine the time when the washing program will finish. 

NOTES:   * 

This function is not available for the DELICATE program. 

*  To avoid water leakage when using this function, make sure the water taps 

are open, the drain hose is properly installed and the washing load and 
detergent are properly prepared.

1.  Put your washing in the machine, loading items uniformly in the tub.
2.  Press the POWER ON/OFF button.
3.  Select the required PROGRAM and/or PROCESS.
4.  Press the PROCESS button until the Delay indicator light flashes, then press the 

SET button to select the desired time period (in hours) for the wash to finish.

5.  Select the water level, if necessary.
6.  Add any detergents (see below and page 17 for details).
7.  Close the washer lid and press the START/PAUSE button.
8.  After setting the delay, the corresponding light will illuminate and all other lights will 

be switched off about one minute later. From this time on until the delayed time 
only the POWER and SET buttons will response when pressed.

9.  To check the delayed program, press the SET button: the program will be indicated 

for 5 seconds. During these 5 seconds you can press the WATER LEVEL button 
and set the water level.

10. To cancel the delay, shut off the power.
11. To change the delay time, first cancel the delay, then set it again.

Adding detergent to a delayed wash

When using the delayed wash, we recommend 
you do not add detergent directly to the wash tub 
but follow the instructions below:
•    

Powder detergent:

 either put powder 

detergent into the detergent box or, if you 
prefer to put it directly into the wash tub, wrap 
the powder in a small cloth.                   

•    

Liquid detergent and bleach:

 pour liquid 

detergent or bleach into the hole on the 
pulsator. Do not pour it directly into the tub as 
it may cause discolouration of your washing.

•    

Fabric softener: 

dilute the softener with twice the amount of water, then pour the 

solution into the softener dispenser on the balance ring.

17

Summary of Contents for STR-WPTL6K

































Reviews: