background image

30

TS 500i

:

Remove the washer (1) and 
rubber ring (2) on the other side

:

Examine guard (3), replace if 
necessary 
– also check the stops (arrows)

– Examine the individual parts, 

replace if necessary

Installation

:

Align the rubber ring so that the 
lug (1) engages in the opening 
(arrow)

:

Press the rubber ring (1) into the 
hole in the guard until it lies flush 

1307RA018 TG

1

2

3

370RA024 TG

1

– Rotate guard

:

Align the rubber ring (2) so that 
the lug (1) engages in the 
opening (arrow)

:

Press the rubber ring (2) into the 
hole in the guard until it lies flush. 
The profile of the rubber ring 
must engage in the mount of the 
guard

:

Place washer (1) on the outside 
of the guard on the rubber ring (2)

– Slide the cast arm into the rubber 

bearing.

1307RA019 TG

2

1

370RA031 TG

1

2

:

Place washer (1) on the 
flange (2)

:

Fit flange (2) on the opposite side 
and align so that the threaded 
holes in the flange (2) line up with 
the holes in the cast arm

– Fit sleeves (1) and springs (2) 

over the screws (3)

:

Insert the screws with sleeves 
and springs in the holes (arrows)

– Insert and tighten the screws

370RA032 TG

1

2

370RA033 TG

2

1

3

370RA034 TG

Summary of Contents for TS 500i























































































































Reviews: