Stihl TS 500i Service Manual Download Page 30

Page: 30 / 118

TS 500i

Remove "cast arm with
guard" (1)

– Block the belt pulley.

Remove screw (1)

Remove thrust washer (2).

Remove the axial clamping ring
(arrow).

Remove the other thrust
washer (1).

370RA017 TG

1307RA366 TG

370RA016 TG

Block the belt pulley (arrow).

Unscrew the nut (left-hand
thread) and remove the washer.

– Pull off the belt pulley (1)

Draw the shaft (1) out on the
other side

Carefully take out the screws
(arrows) – compression springs
are tensioned.

The flange drops down on the other
side.

370RA018 TG

370RA019 TG

370RA020 TG

Remove the cast arm (1)

Remove the sleeves (2) and
compression springs (3)

Check the stop pin (1), unscrew
and replace if necessary

– Reassemble parts in reverse

order

Remove the washer (1) and
rubber ring (2)

370RA021 TG

1307RA017 TG

370RA022 TG

Summary of Contents for TS 500i























































































































Search results

Summary of Contents for TS 500i

Reviews:

Related manuals for TS 500i

Brands by name

Popular brands

Stihl TS 500i, Service Manual

Search results

Summary of Contents for TS 500i

Reviews:

Related manuals for TS 500i

Brands by name

Popular brands