background image

MSE 220 C

English

16

For automatic and reliable lubrication of 

the chain and guide bar – use only an 

environmentally compatible quality 

chain and bar lubricant. Rapidly 

biodegradable STIHL Bioplus is 

recommended.

NOTICE

Biological chain oil must be resistant to 

aging (e.g. STIHL Bioplus)  since it will 

otherwise quickly turn to resin. This 

results in hard deposits that are difficult 

to remove, especially in the area of the 

chain drive and chain. It may even cause 

the oil pump to seize.
The service life of the chain and guide 

bar depends on the quality of the 

lubricant. It is therefore essential to use 

only a specially formulated chain 

lubricant.

WARNING

Do not use waste oil. Renewed contact 

with waste oil can cause skin cancer. 

Moreover, waste oil is environmentally 

harmful.

NOTICE

Waste oil does not have the necessary 

lubricating properties and is unsuitable 

for chain lubrication.

Preparations

N

Thoroughly clean the oil filler cap (1) 

and the area around it to ensure that 

no dirt falls into the tank.

N

Position the machine so that the 

filler cap is facing up.

N

Open the filler cap.

Filling chain oil tank

N

Filling chain oil tank

Take care not to spill chain oil while 

refilling and do not overfill the tank.

N

Close the filler cap.

N

Check the oil level regularly during 

operation.

N

Top up the oil tank when the oil level 

reaches the "min" mark (2) or 

earlier. 

If the oil level in the tank does not go 

down, the reason may be a fault in the oil 

supply system: Check chain lubrication, 

clean the oilways, contact your dealer 

for assistance if necessary STIHL 

recommends that you have servicing 

and repair work carried out exclusively 

by an authorized STIHL servicing 

dealer.

Chain Lubricant

Filling Chain Oil Tank

Summary of Contents for MSE 220 C









































Reviews: