background image

MSE 220 C

English

4

Keep the handles dry and clean – 

free from oil and resin – for safe 

control of the power tool.

Make sure the motor housing is not 

damaged.

To reduce the risk of accidents and 

personal injury, do not operate your 

power tool if it is not properly assembled 

and in good condition.
The connecting cord, mains plug and 

switch are particularly important. Never 

use damaged cords and plugs or 

connecting cords that do not comply with 

regulations.

When you use an extension cord, make 

sure the plug and coupling are 

waterproof or positioned in such a way 

that they cannot come into contact with 

water.
The wall outlet must be equipped with a 

ground-fault circuit breaker or such a 

device must be installed between the 

wall outlet and the power tool. Contact 

an electrician for further information.
Do not drive over, squash or jerk the 

connecting cord. Protect it from heat, oil 

and sharp edges.
Make sure that the conductor cross 

section (wire gauge) of extension cords 

meets the minimum requirements – see 

chapter on "Connecting to Power 

Supply".

To reduce the risk of electric shock:

Always connect the power tool to a 

properly installed wall outlet.

Make sure the extension cord used 

complies with the regulations for the 

intended application.

Check that the insulation of the 

power cord, extension cord, plug 

and coupling is in good condition.

Holding and Controlling the Power Tool

Always hold your power tool firmly with 

both hands: Right hand on the rear 

handle, left hand on front handle, even if 

you are left-handed.

During Operation

Make sure you always have good 

balance and secure footing.
In case of imminent danger or in an 

emergency, release the trigger switch 

immediately.
Your power tool is designed to be 

operated by one person only. Do not 

allow other persons in the work area.

Position the connecting and extension 

cords correctly:

Do not chafe on edges, pointed or 

sharp objects

Do not squeeze through gaps in 

doors or windows

If cords are twisted – unplug the 

power tool and straighten them out

Always unwind the extension cord 

completely from the cable drum to 

reduce the risk of fire from 

overheating.

The extension cord must always be 

behind you. To reduce the risk of 

stumbling, position and mark the 

cord so that it cannot be damaged 

or endanger others.

Keep the connecting cord so that it 

cannot be touched by the rotating 

chain.

When switching on, check that the chain 

is not touching any object or the ground.

Do not leave you power tool out in the 

rain and do not operate it as long as it is 

damp.
Take special care in slippery conditions 

– damp, snow, ice, on slopes, uneven 

ground and freshly debarked logs.
Watch out for obstacles such as tree 

stumps, roots and ditches which could 

cause you to trip or stumble.

If the connecting cord is 

damaged, immediately 

disconnect the plug from 

the power supply to avoid 

the risk of electric shock.

001BA094 LA

The drive motor is not 

waterproof. To reduce 

the risk of a short circuit 

or electrocution, never 

work with the power tool 

in the rain or in wet or 

very damp locations.

Summary of Contents for MSE 220 C









































Reviews: