![background image](http://html1.mh-extra.com/html/stihl/msa-220-t/msa-220-t_instruction-manual_1379628048.webp)
Fault
LEDs on the
battery
Cause
Remedy
Insufficient saw chain
oil in the oil tank.
► Fill up with saw chain oil.
The chain lubrication
system is supplying
insufficient saw chain
oil.
► Increase oil feed rate.
The saw chain is
over-tensioned.
► Tension the saw chain as specified.
The chainsaw is not
being used properly.
► Have correct use explained, then prac‐
tice.
"SAW CHAIN
OIL" LED lights
up in red.
Insufficient saw chain
oil in the oil tank.
► Top up saw chain oil.
► If the "SAW CHAIN OIL" LED continues
to be lit up in red: Do not use your chain‐
saw and contact your STIHL servicing
dealer for assistance.
"SAW CHAIN
OIL" LED flashes
red.
The saw chain oil sen‐
sor is defective.
► Do not use the chainsaw. Consult a
STIHL dealer.
19 Specifications
19.1
STIHL MSA 220.0 T, MSA
220.0 TC Chainsaw
–
Approved battery: STIHL AP
–
Weight without battery, guide bar and saw
chain 2.7 kg
–
Max. oil tank capacity: 220 cm³ (0.220 l)
–
Degree of electrical protection: IPX4 (protec‐
tion against splash water from any direction)
The running time is shown at www.stihl.com/
19.2
Chain Sprockets and Chain
Speeds
The following chain sprockets may be used:
6-tooth for 3/8" P
–
Maximum chain speed according to
ISO 11681: 23.3 m/s
19.3
Minimum Groove Depth of
Guide Bars
The minimum groove depth depends on the pitch
of the guide bar.
–
3/8" P: 5 mm
19.4
STIHL AP battery
–
Battery Technology: Lithium-ion
–
Voltage: 36 V
–
Capacity in Ah: see rating label
–
Energy content in Wh: see rating label
–
Weight in kg: see rating label
–
Permissible temperature range for operation
and storage: -10°C to +50°C
19.5
Sound Values and Vibration
Values
STIHL recommends wearing ear defenders.
–
Sound pressure level L
pA
measured according
to EN ISO 22868: 94 dB(A) The K value for
the sound pressure level is 2 dB(A).
–
Sound power level L
wA
measured according to
EN ISO 22868: 104 dB(A) K-value (uncer‐
tainty) for sound power level is 2 dB(A).
–
Vibration level a
hv
measured according to EN
ISO 22867
–
Control handle: 3.4 m/s². The K value for
the vibration level is 2 m/s².
–
Handlebar: 3.0 m/s². The K value for the
vibration level is 2 m/s².
The vibration levels indicated were measured
according to a standardized test method and can
be used as a basis for comparing electric power
tools. The vibration levels actually occurring may
vary from the values indicated, depending on the
type of application. The vibration levels indicated
can be used for an initial estimate of the vibration
stress. The actual vibration stress has to be esti‐
mated. The times when the electric power tool is
switched off and the times when it is switched on
but running under no load can be taken into
account in the estimate.
19.6
REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
English
19 Specifications
48
0458-007-9621-A