Stihl FC 75 Service Manual Download Page 63

Page: 63 / 70

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

– Remove the drive shaft,

10.3

– Remove the bike handle,

10.1

– Remove the loop handle,

10.2

Version up to 2002

On loop-handled machines,
loosen the clamp screws
(arrows) in the control handle.

936RA232

Version from 2002

Loosen the clamp screws
(arrows) in the control handle.

936RA313

Take the fixing screw (1) out of
the AV sleeve.

Loosen the clamp screw (2).

936RA233

– Pull out the drive tube.

On loop-handled machines, pull
the drive tube (1) out of the
control handle (2) at the same
time.

936RA210

Pull off the throttle cable retainer
(if fitted).

936RA211

Remove the screw (arrow) from
the carrying ring.

Pull the carrying ring apart and
take it off the drive tube.

FH 75, HL 75 only

936RA266

Loosen the screw (arrow) on the
carrying ring.

– Pull off the carrying ring.

Install in the reverse sequence.

936RA067

10.4

Drive Tube

10.4.1 FS 80, 85, FH 75, HL 75

Summary of Contents for FC 75







































































Search results

Summary of Contents for FC 75

Reviews:

Brands by name

Popular brands

Stihl FC 75, Service Manual

Search results

Summary of Contents for FC 75

Reviews:

Brands by name

Popular brands