Stihl FC 75 Service Manual Download Page 25

Page: 25 / 70

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

Take out the screws (arrows).

– Remove the fan housing.

936RA234

On newer machines the fan housing
has been strengthened with ribs (1).

Left: Previous version
Right: New version

936RA314

Use a screwdriver to pry the
retaining ring out of the fan
housing.

– Slip the retaining ring off over the

AV sleeve.

936RA235

Push the service tool (1)
4126 893 4900 into the AV
sleeve as far as stop.

Tighten down the clamp
screw (2) firmly.

If necessary, tighten the fixing

936RA236

screw (3) moderately.

– Apply a few drops of STIHL press

fluid OH 723,

12, between the fan housing

and rubber element.

– Clamp the service tool in a vise.

Pull the fan housing off the rubber
element.

936RA237

Loosen the clamp screw (1) and,
if necessary, the fixing screw (2).

Pull the sleeve (3) off the service
tool.

936RA238

Pull the rubber element off the
sleeve.

Installing

936RA239

Push the rubber element, tapered
end (1) first, onto the sleeve until
the flange (2) is behind the
sleeve.

936RA240

Summary of Contents for FC 75







































































Search results

Summary of Contents for FC 75

Reviews:

Brands by name

Popular brands

Stihl FC 75, Service Manual

Search results

Summary of Contents for FC 75

Reviews:

Brands by name

Popular brands