manualshive.com logo in svg

Stihl FC 75, Service Manual

Share
Download
Stihl FC 75 Service Manual Download Page 61

60

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

:

Push the drive shaft into the drive 
tube until dimension "a" is 
obtained (rigid shaft should 
project 20 mm and the flexible 
shaft 17 mm). If necessary, apply 
slight pressure to the shaft and 
rotate it slowly until it can be 
pushed in to the specified 

VA

936RA265

a

dimension.

– Install the bearing housing – see 

"CombiTools" service manual.

Flexible liner

– Remove the drive shaft.

:

Use hook (1) 5910 890 2800 to 
pull out the plug.

VA

936RA172

1

:

Pull out the flexible liner.

:

The hole (1) must be between the 
spokes (2).

– Fit the plug and then the drive 

shaft.

The drive shaft in the upper end of 
the drive tube is supported in a 
flexible liner. The top end of the 
flexible liner is sealed with a plug 
and the bottom end with a sleeve.

:

Loosen the wing screw (1).

:

Pull the lower end of the drive 
tube (2) out of the coupling 
sleeve (3).

VA

936RA059

1

2

3

:

Loosen the clamp screw (2).

:

Pull the coupling sleeve (2) off 
the upper end of the drive tube 
(3).

VA

936RA060

1

3

2

10.3.1 Drive Shaft in Upper End 

of Drive Tube
(KM 85 only)

Summary of Contents for FC 75







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands