Stihl Cutquik TS 410-A Technical Information Download

Page: 10 / 11

Page 10

Technical Information 19.2010

TI_19_2010_30_01_01.fm

5.8.4

Shroud

Plug connection short circuit wire / control
panel

Press in and/or insert plug connection/wire in
the marked locations (arrows)

Control panel

Route the cable starting at the control panel in the
direction of the plug connection to the short circuit
wire.

Press in and/or insert plug wires in the marked
locations (arrows)

5.9

Tightening torques

Additional tightening torques are listed in the
Service Manual for the STIHL Cutquik

TS 410, 420.

5.10

Service notes

Service and repair procedures are included in the
Service Manual STIHL Cutquik

TS 410, 420.

370TI069 KN

370TI070 KN

Part(s)

Thread

Tightening
torque

Cap / tank housing

P 6x19

6 Nm

Generator /
crankcase

M 4x12

3 Nm

Solenoid valve / tank
housing

P 6x19

6 Nm

Cap / shroud

M 5x17

4.5 Nm

Ground wire /
crankcase

M 4x12

3 Nm

Hose connector /
solenoid

G 3/8"

3 Nm

Summary of Contents for Cutquik TS 410-A












Search results

Summary of Contents for Cutquik TS 410-A

Reviews:

Related manuals for Cutquik TS 410-A

Brands by name

Popular brands

Stihl Cutquik TS 410-A, Technical Information

Search results

Summary of Contents for Cutquik TS 410-A

Reviews:

Related manuals for Cutquik TS 410-A

Brands by name

Popular brands