STIEBEL ELTRON SBP 100 Operation And Installation Download Page 3

OPERATION 

 

General information

EN

GL

ISH

www.stiebel-eltron.com 

SBP 100| 

23

OPERATION

1.  General information

The chapters "Special Information" and "Operation" are intended 

for both the user and qualified contractors.
The chapter "Installation" is intended for qualified contractors.

 

Note

Read these instructions carefully before using the appli-

ance and retain them for future reference.

Pass on the instructions to a new user if required.

1.1  Safety instructions

1.1.1  Structure of safety instructions

!

 

KEYWORD Type of risk

Here, possible consequences are listed that may result 

from failure to observe the safety instructions.

f

f

Steps to prevent the risk are listed.

1.1.2  Symbols, type of risk

Symbol

Type of risk

 

 

Injury 

 

 

 

Electrocution 

 

 

 

Burns

(burns, scalding) 

1.1.3  Keywords

KEYWORD

Meaning

DANGER 

Failure to observe this information will result in serious 

injury or death.

WARNING 

Failure to observe this information may result in serious 

injury or death.

CAUTION 

Failure to observe this information may result in non-seri-

ous or minor injury.

1.2  Other symbols in this documentation

 

Note

General information is identified by the adjacent symbol.

f

f

Read these texts carefully.

Symbol

Meaning

 

 

Material losses

(appliance damage, consequential losses and environmen-

tal pollution)

 

 

Appliance disposal 

 

f

f

This symbol indicates that you have to do something. The ac-

tion you need to take is described step by step.

1.3  Units of measurement

 

Note

All measurements are given in mm unless stated oth-

erwise.

2.  Safety

2.1  Intended use

The appliance acts primarily as a buffer cylinder for heat pumps 

to function as a hydraulic separator of the flow between the heat 

pump circuit and the heating circuit.
This appliance is intended for domestic use. It can be used safely 

by untrained persons. The appliance can also be used in a non-do-

mestic environment, e.g. in a small business, as long as it is used 

in the same way.
Observation of these instructions and of instructions for any ac-

cessories and other system components is also part of the correct 

use of this appliance.
Any other use beyond that described shall be deemed inappro-

priate. Using the appliance for heating fluids other than water 

or for water supplemented with chemicals, such as brine, is also 

deemed inappropriate.

!

!

Summary of Contents for SBP 100





















Reviews: