Stewart Filmscreen Luxus Owner'S Manual Download Page 18 | Manualshive

Page: 18 / 31

background image

Stewart Filmscreen – Luxus

18

IBT-100 for Serial (RS-232C) CONNECTIVITY (IF EQUIPPED)_______

An IBT-100 can be equipped to plug in through the smart port on the back of the Luxus case. This unique
piece of hardware combined with its integrated firmware and optional ancillary software can be used to
interface CS-Bus controllers with external RS-232C networks to enable seamless bi-directional control and
feedback.

GETTING STARTED

Making the Connections

1.

Connect the RJ25 cable to the back of the Luxus
case on the smart port with RJ45 (see Figure 12).

2.

Connect the other side of the RJ25 cable to the
RJ25 female port on the IBT-100 (see Figure 19).

3.

Connect your third party RS-232C connection to
the female RS-232C port on the IBT-100.

RJ25 port

Figure 19. IBT-100, showing RJ25 port

«
...
16
17
18
19
20
...
»

Summary of Contents for Luxus
































Reviews:

No comments

Related manuals for Luxus

Brand: Panasonic Pages: 13

Brand: Optoma Pages: 93

Connect Electric

Brand: Euroscreen Pages: 8

Brand: DNP Pages: 2

Brand: ViewSonic Pages: 2

Brand: Nebula Pages: 74

Brand: BenQ Pages: 28

Brand: Barco Pages: 46

Brand: Barco Pages: 56

Brand: 3M Pages: 4

BRAVIA VPL-HW15

Brand: Sony Pages: 2

BRAVIA HDMI VPL-AW10

Brand: Sony Pages: 77

BRAVIA VPL-HW15

Brand: Sony Pages: 84

Brand: Sony Pages: 83

BRAVIA VPL-VW90ES

Brand: Sony Pages: 168

Brand: AAXA Technologies Pages: 2

BigVizion HDBV5100P

Brand: Optoma Pages: 2

Brand: Vivitek Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands