background image

Luxus

 

15

STI-100 CONTROLLER INSTALLATION (CONTINUED)

CLASS II CONNECTIONS

A 4 pin RJ25 jack provides the connection to any external control equipment  An RJ25 can be 6 pin or 4 
pin, either can be used as follows:

6 Pin

Pin

Signal

1

Not used

2

Common

3

LV1

4

LV2

5

STI

5

Not used

 
LV1 and LV2 are the close contact connections, these require a short to common to activate  An external 
switch or relay should connect this to the common  In the open circuit there is about 5Vdc present on 
the connection  STI is the voltage sensing connection  An external device should connect to this pin and 
common 

Operation

The operation of the STI is based on the state of the LV and STI inputs as follows 

Pin

Signal Applied

Action

LV1 Close

Dry closure

Stays up

LV1 Open

Dry closure

No change

LV2 Close

Dry closure

Down

LV2 Open

Dry closure

None

LV1&LV2 Close

Dry closure

Stop

LV2&LV2 Open

Dry closure

LV1&LV2

Open 0V -> 12V

Down

LV1&LV2

Open 12V -> 0V

Up

4 Pin

Pin

Signal

1

Common

2

LV1

3

LV2

4

STI

Both the STI inputs and LV can 
be used at the same time, as 
illustrated above  There is a 
build in de-bounce function 
whereby the change of a signal 
must exist for a time greater 
than 80ms  Any signal less that 
80ms is ignored 

Summary of Contents for Luxus
























Reviews: