Build Instructions
Final Assembly
51. Following “Landing Gear Detail” on plan set
accurately bend landing gear using needle
nose pliers and included 1/32 in. wire.
52. Trim covering on fuselage to expose landing
gear pocket. Test fit landing gear within gear
pocket of fuselage. Remove.
53. Install wheels of your choosing to landing
gear. We suggest Du-Bro 1-1/4 in. mini lite
wheels [DUB125MW] available at
stevensaero.com. Retain wheels by making a
90 degree bend in gear axle and trimming
excess wire as illustrated on plan set.
54. Install landing gear within fuselage and retain
with 1/32 ply part F19 as illustrated on plan
set. Friction alone should be sufficient to
retain F19 allowing easy removal of landing
gear. If desired, retain F19 and landing gear
within fuselage using CA glue.
55. Paint F20 tail skid to match trim scheme of
model. Open covering in fuselage where tail
skid installs. Fit and bond F20 to fuselage
using medium CA glue.
56. Cut the provided 4 in. length of 1/8 in.
hardwood dowel to 1 and 2 in. lengths
forming front and rear wing retention dowels.
If desired, paint these dowels to match your
trim scheme.
57. Use a hot soldering iron or knife to open oval
pocket at top/center of wind screen to allow
for installation of previously cut 1 in. length of
dowel (step 56). Reference plan set for
installation of forward wing retention dowel.
Bond within fuselage assembly from behind
wind screen and underneath top former F11.
58. Use a hot soldering iron or knife to open
circular pockets immediately aft of rear former
F3 to allow for installation of previously cut 2
in. length of dowel (step 56). Center 2 in.
dowel between fuselage sides through holes
behind rear former F3. Make certain equal
amounts of dowel protrude beyond fuselage
sides on both right and left of fuselage. Once
centered, bond dowel with thin CA glue to
secure rear wing retention dowel.
59. Remove covering from tab on bottom of
vertical stabilizer where it will insert through
horizontal stabilizer and fuselage. Next,
remove covering over notch in top/aft deck of
fuselage to receive vertical stabilizer. Finally,
remove covering from rectangular slot in
center of horizontal stabilizer to allow tab on
bottom of vertical stabilizer to pass through
the slotted horizontal stabilizer.
60. Fit vertical stabilizer through horizontal
stabilizer nesting tab on vertical stabilizer
within slot at top rear of fuselage.
61. Center wing over fuselage and retain using
two #16 rubber bands looped across front and
rear wing retention dowels. Square wing to
fuselage.
62. Check and adjust square of horizontal
stabilizer relative to wing until identical
measurements can be obtained from identical
reference points at wing trailing edge and
outside point of hinge line at stabilizer on both
right and left sides of model. When in doubt,
stand back from model and trust your eye it’s
far more accurate than you give it credit. With
stabilizer squared to wing and fuselage, retain
by gluing with medium CA glue at several
points along fuselage.
Square vertical stabilizer perpendicular to
wing and horizontal stabilizer. Retain
stabilizer with medium CA glue.
63. Open up slot on left side of elevator to receive
one laser cut control horn. Additionally, open
up top push-rod exit slot on left side of
fuselage to allow elevator push-rod to exit. Fit
and bond control horn as illustrated on plan.
64. Open up slot on right side of rudder to receive
one laser cut control horn. Additionally, open
up lower push-rod exit slot on right side of
fuselage to allow rudder push-rod to exit. Fit
and bond control horn as illustrated on plan.
65. Mount PKZ3351 receiver/esc/servo unit
exactly as illustrated on plan set using Du-Bro
RC double sided servo tape [DUB634].
QuickOats™ (100)
- Build Instructions © 2010 Stevens AeroModel, all rights reserved.
Page 12