manualshive.com logo in svg

STEPCRAFT Touch-Probe, Operating And Safety Instructions Manual, Page: 4 / 25

Share
Download
STEPCRAFT Touch-Probe Operating And Safety Instructions Manual Download Page 4

4 

 

STEP 5

 – Insert the brown and white wires into the 5

th

 and 6

th

 terminals 

(counting up from the bottom). The terminals are labeled “Tool” on the 
circuit board. 

Note: It does not matter which wire goes in each terminal.

 

Be sure that the terminal is opened first, by using a small flat head 
screwdriver.  Then once the wires are inserted, tighten each terminal 
with the screwdriver.  

Caution: Do not over-tighten these screws!

 

 

 

 

 

 

 

 

STEP 6

 – Reinstall the circuit board cover, ground wire and two screws. 

 

INSTALLING THE TOUCH PROBE TO THE STEPCRAFT TOOL HOLDER 

There are two basic ways that you can install the Touch Probe to the Stepcraft CNC machine; using the 20mm to 
8mm Tool Adapter (P# 10120 - $14.99) with the 43mm to 20mm (Proxxon) Tool Adapter (P#10107 - $19.99) or 
you can use an 8mm collet in your spindle and mount it like you would an end mill.  

 

USING TOOL ADAPTERS 

STEP 1

 – Gather than Touch Probe, 20mm to 8mm Tool Adapter and 

43mm to 20mm Proxxon Tool Adapter. 

 

 

 

 

 

STEP 2

 – Insert the 20mm to 8mm Tool Adapter into the 43mm to 

20mm (Proxxon) Tool Adapter making sure that the slots in each 
adapter line up.  

NOTE: It will look like the photo on the right when 

assembled outside the machine, but in order to install it in the tool 
holder you will need to install the Touch Probe after the Tool Adapters 
are installed on the Stepcraft’s Tool Holder.

  

 

 

 

 

STEP 3

 – Insert the Tool Adapters into the 43mm Orange Tool Holder 

on the Stepcraft CNC machine from the top. Then insert the Touch 
Probe’s 8mm mounting post into the 20mm to 8mm Tool Adapter from 
the bottom. Tighten either the tool holder bolt or Quick Release Knob (if 
equipped). 

 

 

 

 

 

 

 

 

Summary of Contents for Touch-Probe


























Reviews:

No comments