manualshive.com logo in svg

STEPCRAFT Touch-Probe, Operating And Safety Instructions Manual, Page: 14 / 25

Share
Download
STEPCRAFT Touch-Probe Operating And Safety Instructions Manual Download Page 14

14 

   

 

Next, draw a box with the measurement of your object width (X value) and length (Y value) and add 15mm on 
each value for safe enclosure of the scan. Center this box in your work area.  

 

 

Make a 2D profile tool path of this box. You can select any end mill setting since we are not actually cutting.  Also 
set your spindle speed to zero to prevent the spindle from turning on. This tool path is used by the AutolovelerCA 
plugin defining the area that the Touch Probe will operate to generate the matrix probe points. It will scan 
everything inside the box.  After calculating the tool path, save the file to your computer’s desktop (or in a location 
that will be easy to find) 

 

 

 

Not setting the spindle speed to zero can cause severe damage to the Touch Probe or 
personal injury 

 

SETTING THE TOUCH PROBE POSITION FOR SCANNING 

Mount the Touch Probe on the machine with one of the methods described previously. 

Open UCCNC with the “SC2-XXX 3D Probe” Profile already installed on your machine. Minimize or send the 
AutolevelerCA plugin window to the background by clicking anywhere in the UCCNC window. 

 

 

Next, move the probe to the lowest part of your object and probe the bottom edge of it 

, the machine will zero 

the Y-axis coordinate. 

 

Summary of Contents for Touch-Probe


























Reviews:

No comments