background image

Z3 Roadster

1.

 Carefully remove the passenger glove box assembly by removing the

screws shown in figure 7.

2.

 Locate and remove the passenger's lower side trim panel by removing

the 3 plastic retainers (turn 90 degrees).

3.

 Remove the glove box assembly by lifting up the left side in order to clear

the securing tabs.

3.

 Remove the passengers knee bolster by unscrewing the three 10mm hex

head bolts. 

(Figure 5)

Knee

Bolster

Fig 5

4.

 Remove the lower trim panel. 

(Figure 3)

5.

 Plug in the BMWSTX connector to your BMW's 12 pin alarm port. 

(Figure 6)

6.

 Using the wire tap connect the single RED wire from BMWSTX's alarm

harness to the single black female pin wire.

 

(Figure 6)

(Note: On early production vehicles this wire was installed. IF YOU DO NOT
HAVE A SINGLE BLACK FEMALE PIN LEAVE RED WIRE DISCONNECTED)

7.

 Mount the unit securely to the vehicle. In some cases you will need to

remove part of the lower trim panels insulation. 

(Figure 3)

Go to " LED & Sensor Installation" Pg 4.

Fig 7

4.

 Plug in the BMWSTX's connector to your BMW's 12 pin alarm port.

(Figure 8)

5.

 Using the wire tap connect the single RED wire from BMWSTX's alarm

harness to the single black female pin wire.

 

( Figure 8 )

(Note: On early production vehicles this wire was installed. IF YOU DO NOT
HAVE A SINGLE BLACK FEMALE PIN LEAVE RED WIRE DISCONNECTED)

6.

 Mount the unit securely to the vehicle.

Go to " LED & Sensor Installation" Pg. 4

3

12 Pin

Alarm

Port

BMWSTX Connector

Fig 6

Wire Tap

Black Female

Pin

Red Wire

BMWSTX Connector

& 12 Pin Alarm Port

Single Black Pin

Female Pin

BMWARP

Receiver

Red Wire

Fig 8

REV2  5.12.03

bmwstx  3/10

RECIEVER

 

INSTALLATION GUIDE

automotive security systems

(E-36) 3 Series ( Except 318ti & Z3) 

Summary of Contents for BMWRTX











Reviews: